脉冲电压法检测空心电抗器的FFT波形特征及其故障判别方法

脉冲电压法是检测空心电抗器匝间绝缘故障的有效方法,但其时域检测波形的故障特征识别难度大,本文提出利用其FFT波形特征来判别故障的方法。通过有限元法计算了空心电抗器不同部位故障时线圈组非故障各层线圈电感值及线圈组总电感值的变化规律。为线圈组模型添加脉冲振荡回路,将得到的电抗器两端电压的时域波形利用FFT转换为频域波形。对比分析了不同故障部位的FFT波形变化特征,认为不同故障部位的空心电抗器FFT波形衰减谐振频率的变化是由电感值的变化引起的,为频域故障判据提供了数学支持。以故障线圈组的FFT波形峰值点对应频率为判据,提出了基于FFT波形特征的电抗器故障及故障程度的判别方法,并进行了实例验证。所得结果进一步拓展了脉冲电压法检测空心电抗器匝间短路故障的有效性和精确性,为进一步准确判断空心电抗器匝间短路缺陷提供了方法指导。     

一种雪地轮胎的结构设计

本文介绍了265/70R17115S规格雪地轮胎的设计,外轮廓方面,轮胎的设计外直径797 mm,充气断面宽282 mm,轮胎的行驶面宽207 mm,设计行驶面弧高度8.5 mm,胎圈着合直径取值430 mm,轮胎的胎圈着合宽度237.8 mm,轮胎的断面水平轴位置取值0.96746;轮胎的胎面花纹设计分为长型花纹(M型、L型)与短型花纹(S型),3种花纹为交替变节距呈现,花纹深度10.4 mm,花纹饱和度68.16%。轮胎的施工设计方面:胎面挤出部件为全分层设计,可更好的区分胶种,功能性更强,胎侧挤出部件为双复合设计,冠带层的1#、2#带束层材料使用3×0.30HT钢丝帘线,胎圈部位的钢丝圈为斜六角形结构,更好的保证了成品断面钢丝圈部位,切割后呈近圆形;胎胚成型使用的设备是萨驰一次法成型机,胎胚硫化使用的设备是韩国东和液压硫化机,硫化工艺为氮气硫化。生产的成品轮胎的外缘尺寸、强度性能和耐久性能等均满足国家标准要求。     

Equivalent model of multi-type distributed generators under faults with fast-iterative calculation method based on improved PSO algorithm

There are various types of distributed generators (DGs) with diferent grid integration strategies. The transient char? acteristics of the fault currents provided by the DGs are diferent to those of conventional synchronous generators. In this paper, a distribution network with multi-type DGs is investigated, including consideration of DG low-voltage ride through (LVRT). The fault current characteristics of two typical DGs, i.e. an inverter-interfaced distributed generator (IIDG) and a doubly-fed induction generator (DFIG), are analyzed, considering the specifc operation modes. Based on analysis of the fault characteristics, an equivalent model of the multi-type DGs under symmetrical/asymmetrical fault conditions is established. A fast-iterative fault calculation method for enhancing the calculation efciency while avoid? ing local convergence is then proposed using an improved particle swarm optimization (PSO) algorithm. A simula? tion system of the distribution network with multi-type DGs is established in PSCAD/EMTDC. The simulation results validate the high accuracy and calculation efciency of the proposed calculation method of the fault components. This can assist in the settings of the protection threshold.     

420 kA铝电解槽失电后热场分析及运用

通过建立420 kA铝电解槽的三维模型,并采用有限元分析软件ANSYS Workbench模拟了失电后槽内热场变化情况.重点研究了电解槽失去直流电流输入后电解槽内各个介质的温度变化情况,获取了电解槽失电后随时间延长温度下降情况,得到了电解槽内各个介质的温度随时间下降的曲线.通过仿真分析发现电解槽在失电后30 min各个介质温度变化较小,2 h左右电解质温度下降10℃左右,4 h左右电解质温度下降到了915℃左右,同时分析了电解槽外壳和阳极热通量的情况.建立的稳态温度场与实际测量结果比较,其温度差最大为76℃,最小为7.9℃,个别测量点与实际结果偏差稍大,多数测量点与实际结果较为接近.造成偏差的原因主要是仿真模型存在一定的误差,但大的趋势与实际结果相吻合.仿真研究的结果对电解槽失电后的应急处置及平时的应急管理具有重要的指导意义.     

近终型金属铸造模具制造工艺设计分析与应用

近终型制模技术，可以缩短制模周期、降低生产成本。本文介绍近终型技术在制模工艺实际中的应用概况。并举出实例，指出近终型制模技术可以提高生产效率，快捷地制造出各种复杂的零件/金属模具，该技术有着广阔的应用前景。     

不完备信息系统的规则提取研究*

粗糙集理论和D-S证据理论都是重要的不确定性推理方法,两者各有优缺点.现实生活中,不完备信息系统广泛存在.研究了将两种理论结合用于不完备信息系统以进行规则提取,并用实例进行了验证.     

In-depth investigation on the factors affecting the performance of high oil-absorption resin by response surface method

A series of high oil-absorption resins with low cross-linking degree were synthesized by suspension polymerization using stearyl methacrylate(SMA), 2-Ethylhexyl methacrylate(EHMA), and styrene(St) as monomers.Response surface methodology(RSM) with central composite design(CCD) was also applied to determine the optimal parameters that are mainly known to affect their synthesis. Thus, the effects of the monomer mass ratio(EHMA:SMA), the rigid monomer(St) dosage, the porous agent(acetone) dosage, and their pairwise interaction on the resin's oil-absorption capacity were analyzed, highlighting PSES-R_2 as the resin with the optimum performance. The pure oil-absorption rates of PSES-R2 for gasoline, diesel, and kerosene were 11.19 g·g~(-1),16.25 g·g~(-1), and 14.84 g·g~(-1), respectively, while the oil removal rates from oily wastewater were 98.82%,65.11%, and 99.63%, respectively.     

Effect of high temperature on the mechanical properties of hierarchical porous cenosphere/geopolymer composite foams

A hierarchical porous cenosphere/geopolymer composite foam (FHCs/KGP) was fabricated by the simultaneous incorporation of O₂ pore from hydrogen peroxide and cenosphere filler addition. Effects of both H₂O₂ content and high-temperature treatment on the microstructure, porosity and strength of porous FHCs/KGP foams were investigated systematically. The obtained FHCs/KGP foams showed typical amorphous structure and desirable porosity from 65 to 82%. The composites could crystallize in situ to FHCs/leucite foams above 1000℃. Compression strength of the FHCs/leucite foams showed a maximum value of 5 ± 0.3 MPa when treated at 1000°C. The improvement of mechanical properties for the composite foams was attributed to crack deflection, fractured microspheres and the good bond between the FHCs and matrix. This study could open opportunities to employ cellular foams as alternatives in structure and filtration applications.     

Effect of SiC nanowhisker addition on microstructure and mechanical properties of regenerated cemented carbides by low-pressure sintering

The hardness and toughness of regenerated cemented carbides, in general, are contradictory. Therefore, it is critical to explore regenerated cemented carbides with both high hardness and high toughness. In this study, regenerated WC-8-wt% Co cemented carbide with SiC nanowhisker were prepared by low-pressure sintering. The influence of SiCw contents on the microstructure and mechanical properties of regenerated WC-8-wt% Co cemented carbide was investigated. The results indicated that the hardness, density, flexural strength, and fracture toughness of regenerated cemented carbide first increased and then decreased with the addition of SiCw. The Vickers hardness, density, flexural strength, and fracture toughness could reach 1575 HV, 14.6 g/cm³, 2204 MPa, 16.85 MPa·m^1/2, respectively, with SiCw content 0.5 wt%, which were increased by 14.4%, 0.7%, 12.2%, and 17.3%, respectively, when compared with the regenerated cemented carbide without SiCw. The lowest friction coefficient and the best wear resistance could be also reached when 0.5-wt% SiCw was added. The fracture mechanism of the regenerated cemented carbide contained both transgranular and intergranular fracture through the microscopic observation of fracture surface via scanning electron microscope.     

First-Principles Investigation of the Interfacial Stability,Precipitate Formation,and Mechanical Behavior of Al3Li/Al3Zr/Al Interfaces

Metallurgical and Materials Transactions A - Precipitates including Al3Li, Al3Zr and core–shell structured Al3Li (Al3Zr) produce significant strengthening effects in Al-Li alloys by means of...